9/22/2018
Question from Anthony Mitchell
 
Sorry about the double post, I only just realised how to attach a pic - please see below for the part I am trying to replace. Many thanks!
9/22/2018
Answer from Nate
 
Hi Anthony, please see my response to your post below.
9/23/2018
Answer from Anthony M
 
Many thanks for your prompt response Nate, will place an order shortly!
Answer this question:

9/22/2018
Question from Anthony Mitchell
 
Hi guys, I'm just after the crampon holder for the Dynafit Speed Turn 2.0. I'm a bit confused because I notice a post on 2/12/18 (also from an Anthony!) with a similar question, but his has a 4 bolt pattern, whereas mine has a 2 bolt pattern. If you could confirm that would be fantastic. I can send pics to confirm if necessary.
9/22/2018
Answer from Nate
 
Hi Anthony, I believe the prior post was referring to the number of mounting holes for the toe piece, and not the crampon receptor. The piece you are looking for is listed above as Speed Turn 2.0 Crampon Receptor.
Answer this question:

8/24/2018
Question from François M
 
Hello,
I am looking for a toe plate extension for Radical ST 2.0. I can see plates for ST, for FT 2.0, but did not find the ST 2.0 one. Do you have it?
Thanks!
François
8/24/2018
Answer from jbo
 
Hi François, there are no extensions for the ST 2.0. If you mean the rotating baseplate, that is listed as Radical 2.0 Toe Plate; it is the same for the ST 2.0 and FT 2.0.
8/26/2018
Answer from François M
 
Hello, thank you for your swift reply! I actually mean the carbon powerplate which goes around the toe binding. Not sure how it is called... It is at the top of the photo in attachment, just above the toe binding.
François
8/26/2018
Answer from jbo
 
Hi François, those are found in the drop list as "Radical FT 2.0 Toe Plate Extension". They are sold individually (x1).
8/27/2018
Answer from François M
 
Thank you! I will order the FT plate extension then. François
Answer this question:

4/26/2018
by JDT (downright abused product)
 
Thanks Skimo for having all these spare parts!! I thoroughly notched my Low Tech 1.0 titanium pins after "downright abuse." Skimo had both ti and steel replacement pins for these legacy bindings, so I can continue use these otherwise perfectly good bindings. I bought the steel which should not notch and were less expensive, and they are working flawlessly.
Comment on this review:

4/19/2018
Question from Eric
 
Which screws for radical st 2?
4/20/2018
Answer from Trace Leches
 
Hey Eric. Which screws for the Radical ST 2 are you looking for? Toe mounting screws, heel mounting screws, or the machine screws that install the toe unit to the rotating baseplate?
Answer this question:

4/7/2018
Question from Tony Addino
 
Would you happen to carry binding screws for Dynafit Radical ST ? Will likely be mounting on my Helio 95s that I just ordered from Skimo and wanted to use new screws.

Tony
4/7/2018
Answer from Trace Leches
 
Hey Tony! Absolutely! Do you need toe or heel screws? Also, is this the first gen Radical ST or is it the 2.0 Radical ST?
Answer this question:

3/26/2018
Question from Sam Hansen
 
Looking for 2 crampon clips to go with the set of Radical ST/FT toe Pieces I ordered from Skimo a week ago. Do you guys have any of these? I couldn't find them on the site...

Thanks,
3/26/2018
Answer from jbo
 
Hi Sam, looks like you found them. They are listed as Radical Crampon Receptors.
Answer this question:

3/17/2018
Question from Kuba
 
Hi dears,
does anybody knows how to replace Low Tech excenter unit please ?

Thank you
3/17/2018
Answer from jbo
 
Hi Kuba, you need to pound out the pin, attached either spring (depending on whether you want auto locking), and try to get the pin back in without the parts going everywhere. Good luck!
3/18/2018
Answer from Jakub P
 
Done :) I have auto locking...See short description.

1. Take the old one pin and cut off small piece see picture.
2. This small piece will fix the spring in correct position.
3. Fix the spring in correct position
4. Press the spring with plastic excenter unit and push (pound in) the new pin.
3/19/2018
Answer from jbo
 
Hi Jakub, thanks for the mini-tutorial! Glad you got your binding restored to working order.
Answer this question:

3/7/2018
Question from Adam
 
Will the speed turn crampon receptors work for the Superlite 2.0 crampon receptors? I need the receptor and the screws both. Thanks.
3/7/2018
Answer from Nate
 
Hi Adam, the Speed Turn Crampon receptors won't work with the Superlite 2.0 toes. The crampon receptor you seek for those toes is the LTR/Superlite crampon clip listed above.
Answer this question:

2/23/2018
Question from Nate Page
 
Hi. I am looking for a Vertical FT12 Heel. I think I need the whole thing to fix the lowest walk mode shelf having broken off (see pic)? Thanks!
2/23/2018
Answer from jbo
 
Hi Nate, it looks like you aren't using brakes in which case the "shelf" isn't critical.
Answer this question: