Plum Binding Parts

Wear out a fork? Lose a screw? Decide to add the oddly expensive crampon attachment? Whatever you're into, we will try to help. Find our growing list of parts for Plum bindings below:

Crampon Attachments (x2) - Machined receptors for Oazo and Race 150/170 toe pieces, including the required screws. This attachment system is only compatible with Plum ski crampons, and will not accept Dynafit-style ski crampons. Multiple colors available.

Heel Risers (x2) - Plastic risers that mount onto the forks of Race 145/150/165/170/185 bindings. Mount by punching the pins and removing fork; rotate heels 180 degrees to use. 13g each and gives approximately 25mm of extra height.

Steel Forks (x2) - Replacement forks for Race 145, 150, 170, and 185 bindings, as well as the Oazo 8. Lots of options but not hard to replace.

Titanium Forks (x2) - Shed a few grams from a Plum Race 145-185 or replace notched forks on a Race 135.

Titanium Forks 99 (x2) - Replacement forks for the Race 99 binding.

Titanum Forks R120 / WC (x2) - Titanium replacement U-springs for the Race World Cup and Race 120.

Lock/Unlock Kit (x2) - The humped metal striker plates under the toe levers that enable ski & locked modes. Comes with thin springs to control the lever tension.

Old Race Toe Lever (x1) - A replacement toe lever for model years up to 2015, e.g. 145 & 165. Also works to upgrade pre-2011 toes using the lock / unlock kit to be ISMF compatible.

Race 150/170 Toe Lever (x1) - Replacement toe lever for Race toe pieces belonging to the 2016 vintage and later.

Race 120 Toe Lever (x1) - This is the thinner lever found on the svelte Race 120.

Guide/Yak Toe Lever (x1) - This is the replacement toe lever for Guide and Yak bindings. Comes with a toe lever, spring, and two pins.

Race Toe Lever Springs (x2) - Replacement springs for the toe levers if yours were damaged or scattered to the wind.

Race Toe Lever Pin - The pins that hold the toe lever in place, about which they pivot.

2mm Base Offsets (x2) - Move your Race 145 or 150 heel piece back or forward 2mm by re-mounting with this base pedestal.

3mm Base Offsets (x2) - Re-mount your fixed race heel 3mm fore or aft if you change boots by swapping pedestals.

4mm Base Offsets (x2) - 4mm is a little too close for another drill hole so use this offset pedestal instead.

Oazo Toe Lever - 2020/21 (x1) - Replacement toe ski/tour lock lever. Comes with springs and spring pin.

Oazo Toe Lever - Update for 2021/22 the hole in the lever is smaller to catch more poles. Comes with springs and spring pin.

Oazo High Heel Riser (x1) - Replacement high heel riser for all Oazo bindings.

Oazo Heel Pads (x2) - Removable rubber pads on plates that screw into Oazo heel pieces for additional support. Also works with S170 and Serak bindings.

Pika Heel Pads (x2) - Removable rubber pads on plates that screw into Pika heel pieces for additional support.

Pika Heel Riser (x1) - Heel riser for the Pika (2017+). Comes with hardware required for installation.

Guide Heel Pads (x2) - Removable rubber pads on metal plates that screw onto the heel pieces for extra boot support.

Guide Heel Pins (x4) - Replacement heel pins for the Guide binding; Plum recommends replacing all 4 at the same time.

Guide Heel Roof (x1) - The metal top with climbing post that comes stock on most Guide heel pieces.

Guide Roof Screw (x1) - The mini Torx T9 screws that hold the roofs onto the heel pieces.

Summit Toe Plate (x2) - Base plates to create a wider mounting pattern for Guide toes. 48 grams each with the included machine screws to attach a toe. Also comes with a set of mounting screws.

Race Mounting Screw (x1) - Specialized screws from Plum that are the perfect size for their race bindings.

Race Adjustment Screw (x1) - Torx T25 fasteners that stop the Race 165 / 170 / 185 and Oazo heels from sliding back or forward.

Race Adjustment Nut (x1) - 5mm replacement nut for under adjustment plate. Will work for ATK as well.

Race / Oazo Crampon Attachment Screw (x1) - The tiny Torx screws that hold the crampon receptors onto the Race or Oazo toes.

Guide Mounting Screw (x1) - The countersunk Pozidriv wood screws used to mount Plum Guide bindings.

Guide Adjustment Screw (x1) - Replacement Torx T25 screws used for the Guide and Yak heel fore/aft adjustment systems.

Vertical Release Screw (x1) - Screw used to adjust the vertical release on the Guide, Yak, and WEPA bindings.

Torx T25 Tool - The fore/aft adjustment tool that ships with Guide and Race 165/170/185 bindings.

Fuse Cord for Leash (x2) - Fuse cord attachment to install on boot and attach leash to; alternative attachment for Plum leash.

Grease Spray - Some nice binding grease for moving parts like toe springs. Comes in a 15ml (1.5oz) spray bottle.

T-20 Mounting Screw (x1) - Mounting screw for the Race 140, Serak, and S170 bindings.