what all should I order to replace this missing piece? The backing plate is all that's left. These are a 2015 version of the Scarpa Gea RS.
-Looks like maybe a new canting nut (or not necessary)? I do have the old one, that's the only piece left.
-a canting cam
-but what about that larger missing ring? I couldn't identify a part which matched up that one but may be overlooking.
Also, would I need any specialized tools for this repair, ones beyond the basics in my toolset (wrenches, screw drivers, etc.) What kind of glue is best? Perhaps just loctite?
Thanks,
Anna
SCARPA Hardware
Find replacement hardware for SCARPA boots here. All parts sold as individuals unless noted otherwise.
Alien 1.0 Cuff Bushing - The bushing that helps your boot walk and is probably worn out if you’re looking for it.
Alien 1.0 Knurled Cuff Spacer - A ridged spacer used in the cuff pivot of the Alien 1.0 (old model).
Alien 1.0 Outside Cuff Washer - The outermost washer on your Alien 1.0 (old model) that helps keep the bolt tight while retaining walking ability.
Alien 1.0 Cuff Nut - The hexagonal threaded cuff nut that works in conjunction with the outside cuff washer and cuff screw to assemble the cuff pivot.
Alien Cuff Nut - The threaded cuff nut that works in conjunction with the outside cuff washer and cuff screw to assemble the cuff pivot.
Alien Cuff Screw - The screw that holds the Alien cuff pivot together.
Alien Outside Cuff Washer - The outside cuff washer for the first-generation Alien.
Alien Powerstrap Holder - The little clip that attaches onto the cuff of the Alien. Easy to lose but even easier to replace.
Short Rivet - Short rivest for buckels and eyelets for the Alien 1.0 and 3.0
Alien RS Rivet Long - The rivet used to affix cable guides and the leash ring to the cuff of the Alien RS.
Alien Tongue Screw - The small torx screw that attaches the tongue and Boa assembly to the shell of the boot.
AT Boots Catch Screw - The screw that bolts your ski/walk lever or buckle catch to your cuff or lower shell.
F1 Inside Cuff Nut - The nut that goes on the inside of the cuff pivot to help keep everything tensioned appropriately.
F1 Outside Cuff Washer - The external cuff washer that keeps your boots walking freely and looking pretty on an F1 or the outside lateral cuff pivot of a Maestrale or Gea 2.0/3.0.
F1/F1 LT Buckle Rivet - The rivet that attaches the cuff buckle to the cuff of F1-series boots.
F1/Maestrale/Gea Tongue Screw - The screw that attaches the tongue of the F1/Maestrale/Gea to the lower shell.
F1 Cuff Pivot/Freedom Buckle Ladder Screw - The screw that secures the cuff pivot on the F1 and F1 LT. Used as the outside lateral cuff screw on Maestrale or Gea 2.0/3.0 boots. Also attaches the ladder to the Freedom series boots.
Maestrale/Gea RS 2.0 Ski/Walk Mech Screw - The screw holding the Ski-Walk mechanism onto your Maestrale or Gea RS 2.0 boot.
Maestrale/Gea RS 2.0 Cuff Nut - The nut for the lateral cuff pivot on your Maestrale or Gea RS 2.0. Goes with the F1 Cuff Pivot screw.
Maestrale/Gea RS 2.0 Cuff Screw Blk - The screw that holds the inside cuff pivot and instep strap together.
Maestrale/Gea RS 2.0 Instep Strap Nut - The nut that holds both the inside cuff pivot and the instep strap.
Maestrale/Gea RS 2.0 Instep Buckle Rivet - The rivet that fastens the instep buckle to the boot.
Maestrale/Gea RS 2.0 Instep Buckle Washer - The washer that prevents the Instep Buckle Rivet from sliding out.
Maestrale/Gea RS 2.0 Upper Wave Catch Nut - The nut that holds the end of the Wave Cable to the boot shell below the instep buckle.
Maestrale/Gea RS 2.0 Shell Wave Cable Guide - The black piece that guides the Wave Cable back around on the lower shell nearest the toe.
Maestrale/Gea RS 2.0 Wave Cable Guide Nut: The nut that affixes the Wave Cable Guide to the boot.
Maestrale/Gea Shell Cable Screw - The screw that affixes both the toe-end of the Wave Cable as well as the Cuff Buckle Catch.
Outer Cuff Screw - A silver screw that holds the outer cuff pivot together on Maestrale/Gea series boots.
Rivet Holder - A metal washer for anchoring rivets that is used by the Maestrale, Gea, Alien, F1, F1 LT, and Alien RS.
Rear Tech Fitting - An individual heel fitting. Compatible with most any tech boot. (screw not included)
Square Inside Cuff Nut - Nut for the cuff pivot on first gen Maestrale/Gea boots.
Tech Heel Sole Screw - Screw that is used to mount Rear Tech Fitting to the heel of the boot.
Related Products
» Browse more
SCARPA Boot Parts
Questions & Reviews
11/30/2022
11/30/2022
Hi Anna,
The parts that you need for a full replacement on the outer pivot point on the GEA are as follows:
F1 Cuff Pivot/ Freedom Buckle Ladder Screw
F1 Inside Cuff Nut (this is the part that you already have)
F1 Outside Cuff Washer
As for tools, all you will need is two allen wrenches and blue loctite!
The parts that you need for a full replacement on the outer pivot point on the GEA are as follows:
F1 Cuff Pivot/ Freedom Buckle Ladder Screw
F1 Inside Cuff Nut (this is the part that you already have)
F1 Outside Cuff Washer
As for tools, all you will need is two allen wrenches and blue loctite!
11/30/2022
thanks so much for this quick reply, Tristan! One point of clarification -
As for the F1 inside cuff nut, this actually looks different than that backing plate looking part I mentioned was still remaining in the first post.
I couldn't add two photos to my original, so here's what I'm referring to:
It looks most like the Canting Nut, not the F1inside cuff nut.
Thanks!
As for the F1 inside cuff nut, this actually looks different than that backing plate looking part I mentioned was still remaining in the first post.
I couldn't add two photos to my original, so here's what I'm referring to:
It looks most like the Canting Nut, not the F1inside cuff nut.
Thanks!
Answer this question:
4/2/2022
Hi! Wondering if\when you will have any Maestrale tongue hinges in stock.
Thanks!
Thanks!
4/2/2022
Jordan, Skimo always has these parts on order. I just checked, and Scarpa is out for the foreseeable future. So I can't say when they will be back in stock.
Answer this question:
2/18/2022
Hi there,
I have lost cuff catch on my Scarpa Maestrale boots
I need to order it as soon as possible. I have found the exact catch but couldn't find it's nut and screw, not sure how it is listed above
Please tell me the name of nut and screw. Thank you in advance
I have lost cuff catch on my Scarpa Maestrale boots
I need to order it as soon as possible. I have found the exact catch but couldn't find it's nut and screw, not sure how it is listed above
Please tell me the name of nut and screw. Thank you in advance
2/19/2022
Hey Nika, for the screw you will need the Maestrale/Gea Shell Cable Screw. The nut for the older Maestrale boots cuff catch is actually the same as the F1/Alien 1.0 Ski/Walk Lower Latch Nut, which is in a different listing: SCARPA Ski-Walk Mechanism Parts. Hope that helps!
Answer this question:
2/9/2022
If I want to replace all of the cuff pivot hardware on a pair of 2017/2018 F1s, should I be ordering 4x of the following?
- F1 Inside Cuff Nut
- F1 Outside Cuff Washer
- F1 Cuff Pivot/Freedom Buckle Ladder Screw
Thanks
- F1 Inside Cuff Nut
- F1 Outside Cuff Washer
- F1 Cuff Pivot/Freedom Buckle Ladder Screw
Thanks
2/10/2022
Thanks for reaching out, Jake. You're correct!
Answer this question:
2/6/2022
Hi SkimoCo!
Yesterday I broke the rivet that connects the cam hook for the laces on my Scarpa Alien RS to the plastic of the boot. I think I can probably get by with a hardware store rivet, but would just as soon buy the right parts...
I THINK I need the "alien RS rivet long, yellow... Does that seem right? Do I need another half for the rivet, whether it's an actual rivet part or like, a screw or something? The plastic housing looks undamaged, I just need to reattach that cam hook to the book shell. I'm happy to order a few parts and go with whatever works, if that's what you'd suggest.
Thanks SkimoCo! Love you guys/gals!
Yesterday I broke the rivet that connects the cam hook for the laces on my Scarpa Alien RS to the plastic of the boot. I think I can probably get by with a hardware store rivet, but would just as soon buy the right parts...
I THINK I need the "alien RS rivet long, yellow... Does that seem right? Do I need another half for the rivet, whether it's an actual rivet part or like, a screw or something? The plastic housing looks undamaged, I just need to reattach that cam hook to the book shell. I'm happy to order a few parts and go with whatever works, if that's what you'd suggest.
Thanks SkimoCo! Love you guys/gals!
2/7/2022
Hello Paul! That is the rivet you need. It's just the single piece and you'd likely need a rivet press to get that in properly.
Answer this question:
1/15/2022
Hi! I am looking for a replacement hinge for the tongue of my boot. 1 hinge has broken where the metal bends to meet the screw. Seems like its not a part sold many places. Recommendations welcome!
1/15/2022
Hi Dan,
It sounds like you are looking for a Maestrale/Gea Tongue Hinge, which can be found in the drop down above! If you have further boot questions, feel free to reach out to help@skimo.co.
It sounds like you are looking for a Maestrale/Gea Tongue Hinge, which can be found in the drop down above! If you have further boot questions, feel free to reach out to help@skimo.co.
12/14/2024
Is this part still in stock? i dont see it on the drop down anymore
Answer this question:
12/19/2021
Hello, Do you carry the screw and nut as shown on Scarpa Web site, https://www.scarpa.com/kit-wide-midstrap-wire-pair-21mm-24-5-25-0
I need it for T2 Eco Scarpa(Green), as shown in the attached picture
If you have it, which item on your website is it?
Thank you
I need it for T2 Eco Scarpa(Green), as shown in the attached picture
If you have it, which item on your website is it?
Thank you
12/28/2021
Gregory,
Apologies for the delay! It would appear that we only have the screw which we call the Freedom Outside Cant Screw (Part #420.2). We do not have the backing nut, which is Part #425.14. You may be able to contact SCARPA directly for that part. Hope this helps!
Apologies for the delay! It would appear that we only have the screw which we call the Freedom Outside Cant Screw (Part #420.2). We do not have the backing nut, which is Part #425.14. You may be able to contact SCARPA directly for that part. Hope this helps!
Reply to this comment:
11/23/2021
Any advice on how to retrofit an old t-race telemark boot with ski/walk hardware?
11/23/2021
Hey Xander,
This is a tricky one; honestly, I would just remove the forward lean mechanism and ski the boot in "walk mode;" once you tighten the buckles the boot should still have ample stiffness for a 75mm telemark turn. You'll have to get pretty crazy with a dremel if you want a true ski/walk switch, but if you're ambitious enough to go for it I would use the Scarpa F1 ski/walk mechanism and catch and you'll have to dremel plastic off of the boot until it's flat enough to mount the hardware. You'll want the smallest size of lever as AT boots typically have the mechanism higher up on the cuff than you'll be able to install it. All of our Scarpa ski/walk parts can be found on this page.
This is a tricky one; honestly, I would just remove the forward lean mechanism and ski the boot in "walk mode;" once you tighten the buckles the boot should still have ample stiffness for a 75mm telemark turn. You'll have to get pretty crazy with a dremel if you want a true ski/walk switch, but if you're ambitious enough to go for it I would use the Scarpa F1 ski/walk mechanism and catch and you'll have to dremel plastic off of the boot until it's flat enough to mount the hardware. You'll want the smallest size of lever as AT boots typically have the mechanism higher up on the cuff than you'll be able to install it. All of our Scarpa ski/walk parts can be found on this page.
Answer this question:
11/20/2021
Hi,
I'm looking for the screw and nut which secure the topmost buckle on a gea boot, not sure how it's called.
Can you please help?
Thanks a lot
I'm looking for the screw and nut which secure the topmost buckle on a gea boot, not sure how it's called.
Can you please help?
Thanks a lot
11/20/2021
Thanks for reaching out, Ben. We don't have the schematic for this generation of GEA (pre-2018), so I can't be sure which exact Scarpa part should be used. However, you should be able to find a suitable replacement at your local hardware store. Please let us know if you have any other questions!
Answer this question:
4/24/2021
Hi the screw and washer fell out on my 2017 Maestrale. what are the exact names of these parts?
Thanks!
Thanks!
4/24/2021
Hey Kai, thanks for reaching out! Send us a few photos of your boots(both broken and intact) to "help@skimo.co", and we'll see what we can find for you!
Answer this question:
4/19/2021
I am looking for the screw and washer for the outside cuff hinge. I cant tell exactly which parts might work.
4/19/2021
Adam- You are looking for this part for the bolt "Maestrale/Gea RS 2.0 Cuff Screw Blk". The washer we have not carried. Hopefully, we will have those parts back in stock in the fall.
Answer this question:
4/12/2021
Hi Tristan
Can't find these on above lost. Do you still have them? Or simply run out of stock? I'm interested to buy.
Be grateful for answer.
Can't find these on above lost. Do you still have them? Or simply run out of stock? I'm interested to buy.
Be grateful for answer.
4/13/2021
Thanks for your question, Pawel. I am unable to find any context for your question. Please reach out to us at help@skimo.co and we'll help you out!
Answer this question:
3/29/2021
I'm looking for the screw outlined in the picture. These are Scarpa Maestrale XT boots. Thanks!
3/29/2021
Marcus, thanks for reaching out. That particular screw, which we are out of at the moment, is the F1/Maestrale/Gea Tongue Screw. Please feel free to reach out at help@skimo.co and we can send you a notification when they're back in stock.
Answer this question:
3/22/2021
Hi there,
I’m looking for 3 screws and 3 square nuts for a pair of T1’s. Do you know if any of your square nuts fit? Thanks.
Jeff
I’m looking for 3 screws and 3 square nuts for a pair of T1’s. Do you know if any of your square nuts fit? Thanks.
Jeff
3/23/2021
Thanks for your question, Jeff. It's hard to say without having your boot in hand. You should be able to pick up something that fits at your local hardware store! Please let us know if you have any other questions.
Answer this question:
3/15/2021
Looking for these parts
3/16/2021
Thanks for reaching out, Peter. We would encourage you to contact Scarpa directly for older Maestrale parts. Please let us know if there is anything else we can do for you!
Answer this question:
3/5/2021
Hey Brett, thanks for the soldering iron trick. I got it to break down the loctite and get all the nuts out. Now that I have it apart, how to I get the bushing out of the cuff?
3/5/2021
Hey Chris, we're glad that worked out! To get the bushing out, simply pull the cuff gently up and push down on the exposed plastic lip of the bushing. It shouldn't require too much force to get it out of there. Please send us an email to help@skimo.co if you have any other questions!
Answer this question:
3/2/2021
Can the pictured Maestrale 1.0 instep buckle be repaired or replaced?
3/2/2021
Thanks for your question, Jeff. If the sole issue is the rivet that's popped out, you might be able to come up with a fix from the local hardware store. The buckle can be replaced, however, we only stock the instep buckle for the current generation. Please let us know if you have any other questions!
Answer this question:
3/1/2021
I have a lot of play in the cuff of the old Alien 1.0 boots (cuff seems to move up and down).
I just ordered some new bushings (last two left, so will need to figure out how to replace the other two), but I'm having trouble getting the hex nut off. Any tips? Is it a 14mm or 15mm size?
Also, any other tips to reduce the play in that joint?
Thanks,
Chris
I just ordered some new bushings (last two left, so will need to figure out how to replace the other two), but I'm having trouble getting the hex nut off. Any tips? Is it a 14mm or 15mm size?
Also, any other tips to reduce the play in that joint?
Thanks,
Chris
3/2/2021
Thanks for your question, Chris. It sounds like you're on the right track to reduce the cuff play. Scarpa typically uses Loctite when installing that part, which can make it hard to get apart. Taking a soldering iron and placing it on the center of the cuff nut (on the inside of the boot) can help warm up the Loctite, thus making it easier for removal. The cuff nut doesn't have any shaping, however, the cuff screw is a 3mm allen key. Please let us know if you have any other questions!
Answer this question:
2/27/2021
Looking to replace this item also.
Thanks
Thanks
2/27/2021
Hi Scott,
You are looking for the Maestrale/Gea tongue hinge listed above!
You are looking for the Maestrale/Gea tongue hinge listed above!
Answer this question:
2/27/2021
Looking for the hardware to replace the missing stuff in the photos.
Thanks!
Thanks!
2/27/2021
Hi Scott,
Would you be able to send an email to help@skimo.co with a list of all of the items that you are missing?
Currently, it looks like you are missing the rivet that holds the instep buckle in place. To replace that part, you will need a large rivet and a rivet press. However, a t-bolt will also do the trick, can be sourced at your local hardware store, and does not require a rivet press!
Would you be able to send an email to help@skimo.co with a list of all of the items that you are missing?
Currently, it looks like you are missing the rivet that holds the instep buckle in place. To replace that part, you will need a large rivet and a rivet press. However, a t-bolt will also do the trick, can be sourced at your local hardware store, and does not require a rivet press!
Answer this question:
Earn store credit by writing reviews. Learn more.
